• Casual Friday Link Up
  • Casual Friday Link Up
  • Casual Friday Link Up
  • Casual Friday Link Up
  • Casual Friday Link Up

DIY Marquee Letters


When we walked through the backyard of the Parade Home in it’s final stages, the builders said they wanted something with impact. Something large, fun and eye-catching. We tossed around a few ideas and she mentioned how much she loved my Illuminated Letters from my Little’s Room post.

And I’m pretty sure we were both thinking the same thing at that point.


DIY Marquee Letters by TwoThirtyFiveDesigns.com


She wanted large, as big as we could go for the back porch and we were pretty close to making the letters eight foot and lean them against the wall.
But we opted to put them in the extra garage with the glass garage door in the back yard area. Its essentially an extra room, since we decided to make it a game area for the show, and all agreed they would be perfect in there. I dropped the size down to four foot in height so we could mount them above the galvanized steel panels.

Large DIY Marquee Letters by TwoThirtyFiveDesigns.com

Couple sheets of Plywood found at Home Depot. Thickness depends on if you are going to attach it to the wall or lean it. This was pretty darn thick.
Strand of Outdoor Light Bulbs per letter, found at Target.
Ryobi Jigsaw. Seriously guys….if you don’t already have one, run and grab one now. It seriously cut through this crazy think plywood like butter, like butter people.
Ryobi Corner Cat Sander. We wanted a rustic look, so I didn’t sand a ton, just the edges so they were crazy jagged.
Ryobi Drill. Use a drill bit about the same size as the bulb attachment on the strand of outdoor lights.
Screws if needed to attach to the wall.
Ryobi Impact Driver to mount the letters.

1. I set up a projector and used a photo editing software to trace my letters, according to the size that I needed.
2. After tracing, I cut out each letter with my Jigsaw, sanding any rough edges quickly with my hand sander.
3. I measured out the strand of lights on each letter, marking exactly where I wanted all the lights to be, making sure the cord was not pulled to tightly. Also, plan beforehand how you will make each plug attach to the next plug/letter.
4. Using my drill and drill bit, I drilled out a hole per light for every mark I made on each letter.
5. Carefully unscrew each bulb and run the base through the backside of the letter/each hole, and screw back in each bulb as you go.
6. Depending on if you mount your letter, lean or whatever your preference is, you can tuck and/or tape the extra cord behind the letters. I mounted mine with 2 1/2″ anchor screws into a stud and tucked the excess cord behind the letters.

And viola! A large impact for a great price. Now that can’t be beat!




DIY Large Marquee Letters TwoThirtyFiveDesigns.com

Marquee Letters by TwoThirtyFiveDesigns.com Marquee Letters TwoThirtyFiveDesigns.com

Large DIY Marquee Letters by TwoThirtyFiveDesigns.com

Large DIY Marquee Letters by TwoThirtyFiveDesigns Large DIY Marquee Letters TwoThirtyFiveDesigns.com

DIY Marquee Letters TwoThirty~FiveDesigns.com DIY Marquee Letters TwoThirtyFiveDesigns.com


Want to see the other projects from this series?

DIY Copper Herringbone Side Table

DIY Copper Herringbone Side Tabel TwoThirtyFiveDesigns.com

DIY Copper Pyramid Wall Art

How To Make A Copper Pyramid Out Of Fence Supplies TwoThirtyFiveDesigns.com

DIY Copper Spring Desk Lamp

DIY Copper Spring Desk Lamp TwoThirtyFiveDesigns

And be sure to head on over to Ryobi Nation! One of the best places where I go to find inspiration and win free tools! Now that’s a win win, right?

Share on Facebook49Pin on Pinterest8.4kTweet about this on Twitter15Share on Google+28Share on StumbleUpon52Share on LinkedIn0Share on TumblrEmail this to someone

Recent Posts